Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
Are you looking for ideas about Installing A Bathtub?
Installing a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old tub is easily obtainable, the task can move rapidly; if you need to open up a wall to eliminate the old bathtub and also place the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the task as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally check the overflow outlet as well as the typical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been used a minimum of when as this will certainly resolve it right into its last placement.
Planning for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece about A Step-by-Step Guide to Installing a Bathtub when surfing the web. Sharing is good. You just don't know, you might be helping someone out. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Book My Estimate
Report this page